Bantam BRC-40 Military Jeep Engine Continental Motor Co. BY4112 4 cal 112cid 45bhp @ 3,500 rpm
The Bantam BRC-40 Army Jeep followed the Bantam GPV and the Bantam BRC-60 as the prototype Army jeeps. The full story of the development of the original Army Jeep of World War II is on the linked page. Additional photos are found in the Military Jeeps section of the Military Vehicle Charts.
Bantam Reconnaissance Car BRC-40 as delivered to the Army, 1941.
Bantam BRC-40 Military Jeep
American Bantam Car Company BRC-40 Assembly Line, Butler, PA, 1941.
The success of the Army trials with the American Bantam Car Company BRC-60 prototype jeep led to approval of a 1,500 unit order from Bantam, subject to some improvements in the design. The Bantam BRC-40 (where BRC means Bantam Reconnaissance Car) with squared fenders, headlights partly recessed in the fender and a flat grill, was the result of that redesign.
In 1941, Bantam entered into an agreement with Checker Car Company (maker of the famous Checker Cabs) to build BRC-40 jeeps. This may have been done in an effort to convince the Army that there was no issue regarding Bantam's production capacity, but little is known of the details of the arrangement. A few Checker-built prototype vehicles were delivered to the Army. Photographs have survived as well as one of the jeeps which resides in the Gilmore Car Museum in Hickory Corners, MI.
The BRC-40 met all the Army requirements and was well liked. Additional BRC-40 vehicles were ordered for Lend Lease shipments to Allied nations for an eventual total of 2,642 BRC-40s produced by Bantam. But the Army didn't want to bet on tiny American Bantam to supply the potential huge production requirements that would soon be required for World War II. After a series of political maneuvers and trials involving the designs from Bantam, Ford, and Willys Overland, the contract was awarded to Willys to build a vehicle remarkably like Bantam's design. American Bantam never again built jeeps but was given a contract for trailers as a consolation prize.
One of the original BRC-40s manufactured in 1941 can be seen at the Butler County Historical Society Museum in Butler, PA, site of the American Bantam factory.
Bantam BRC-40 Specifications
| Engine | Continental Motor Co. BY4112 4 cal 112cid 45bhp @ 3,500 rpm |
| Torque | 83 pound-feet |
| Transmission | 3 speed synchromesh Warner Gear T84 |
| Transfer case | Spicer Dana 18 two speed |
| Gear Shift | Floor mounted |
| Axles | Spicer Dana 4.88:1 23-2 rear, Dana 25 front |
| Wheelbase | 79 inches |
| Weight | 2,070 lbs |
Assessment
- Visual Inspection of the Piston (05/04/2012)
- Hyundai, Kia sued by Toyota foe in patent fight over hybrids (19/02/2012)
- 2012 Jeep Wrangler Unlimited Rubicon Photos (19/02/2012)
- California considering Honda hybrid settlement objection (15/02/2012)
- 5 U.S. states reconsider Honda hybrid settlement (15/02/2012)
- Toyota raises earnings forecast (12/02/2012)
- Nissan quarterly profit rises 3.2 per cent (12/02/2012)
- Regulators probe door fires in 2007 Toyota Camrys, RAV-4s (12/02/2012)
- Married drivers get fewer tickets than common-laws: study Read (12/02/2012)
- Lexus Rx300 Repair Manual (05/02/2012)
- New F2012 Ferrari (05/02/2012)
- What will you do at Chiacago Auto Show? (05/02/2012)
- Ford Ranger repair manual Full (1998-2002) (05/01/2012)
- ZF transmission for man (29/11/2011)
- Honda Accord 2008 - 2009 Service Manual (12/11/2011)
| More | ------------- |











